Create mount point to windows share

At the cluster disk selection you must select the root drive for installation. The mounted drives are not available, attempting to select one of the mounted volumes causes setup to direct you to select the root tree drive in my case cluster Disk 6 M:.

Post installation, these are the new SQL server folders under the mount points when viewed through explorer. Notice that the mount points now have a different icon and not the standard Windows folder icon. This should give you more of an understanding of mount points and how they are set up. They operate just the same as any other folder with the exception that permissions grants are handled by each individual mount point and not by the root directory.

Granting permissions at the root drive and pushing child inheritance will not affect the mount points. Still, they are essentially NTFS folders and, as the screenshot above shows, look seem less to the Windows filesystem. As you can see they are also an excellent way to bypass the Windows 26 drive letter limitation.

As always, test this in an offline environment, virtual machines make a great test lab and are extremely easy to set up using my three part guide on this site. Have fun and of course, post back if you have any troubles.

Log in or register to rate. Join the discussion and add your comment. What are Mount Points? Our basic example is as follows Root disk 1 M: Windows disk 2 Multiple mount points are employed in the following configuration for a single instance, remember each of these mount points is actually a separate physical drive from Windows disk management.

With Mount Points it's important to remember the following pointers Do not install software to the root of the mount point. Rather, create and install into a folder under the mount point to allow the correct propagation of permissions.

Ideally, the root drive should not have any data created upon it, it is merely the root tree for the new volumes. Permissions applied to the root drive file system do not propagate to the mount point file systems, they are controlled separately. Mount points are not supported for all SQL Server configurations in case you had a burning desire to use them. If you use the root host volume exclusively for mount points, the size of the host volume only has to be several MB.

This reduces the probability that the volume is used for anything other than the mount points. In a cluster, where high availability is important, you can make redundant mount points on separate host volumes. This helps guarantee that if one root host volume is inaccessible, you can still access the data that is on the mounted volume through the other mount point. Note Because the user data that is on LUN3 depends on both D: and E: volumes, you have to temporarily remove the dependency of any failed host volume until the volume is back in service.

Otherwise, the user data that is on LUN3 remains in a failed state. For more information about how to create volume mount points from a command prompt, click the following article number to view the article in the Microsoft Knowledge Base:. There are three ways to add mount points to a system clustered and non-clustered are the same : Logical Disk Manager Diskmgmt.

You cannot create mount points on the Quorum disk. How to set up volume mount points on a Clustered Server Log on locally with administrative rights to the node that owns the root disk, into which you are going to be grafting the directory. Open Cluster Administrator CluAdmin. Partition the disk, and then create the mount point. Select the disk that you would like to graft into the directory. Right-click the free space on the disk, and then click New Partition.

Create a Primary Partition, and then click Next. Set the size of the partition. Create the new Disk resource, and then set dependencies. To do so, follow these steps: Open Cluster Administrator.

Make sure all nodes are possible owners, and then click Next. Right-click the new Disk resource, and then click Bring Online. With your subscription - you'll gain access to our exclusive IT community of thousands of IT pros. We can't always guarantee that the perfect solution to your specific problem will be waiting for you.

If you ask your own question - our Certified Experts will team up with you to help you get the answers you need. Who are the certified experts?

How quickly will I get my solution? We can't guarantee quick solutions - Experts Exchange isn't a help desk. We're a community of IT professionals committed to sharing knowledge. If no volume is specified, the select command lists the current volume with focus. You can specify the volume by number, drive letter, or mount point folder path. On a basic disk, selecting a volume also gives the corresponding partition focus. Assigns a drive letter or mount point folder path to the volume with focus.

If no drive letter or mount point folder path is specified, then the next available drive letter is assigned. If the drive letter or mount point folder path is already in use, an error is generated. Using the assign command, you can change the drive letter associated with a removable drive.